PTO/Wet Line Kits WA06 Series WA08 Series The WA06 series PTO has been designed to work with most of the existing transmissions in the market. It is a very durable PTO with a wide range of input gears, shifters, speed ratios and output shafts to meet market applications. The WA08 PTO is our WA06 PTO with the ability to mount on the 8 Bolt Transmission opening. This design uses no adapter plates and cuts down on leaks and installation time. It has an “A” ratio that is not offered in the WA06 model. It is a very durable PTO with a wide range of input gears, shifters, speed ratios and output shafts to meet market applications. Meritor Transmissions WA08 Left Side Mount WA06 Right Side Mount Eaton/Fuller Transmissions WA8S or WA8G If WA8G (bottom mount) use stud kit MW1WA20-03-1116 and use WA8S PTO Series WA6S or WA6G If WA6G use stud kit MW1WA20-03-1071 and use WA6S PTO Series Mack Transmission WA8D Left Side Mount - exceptions apply, please check applications WA6D Right Side Mount - exceptions apply, please check applications Note: All PTOs are stocked without an air shift installation kit. If installation kit is needed please add P/N MW1WA101X for single controller POWER TAKE-OFF UNITS Power Take-Off Units ∙ PTO Controls & Accessories ∙ Tanks Hydraulic Hose & Fittings ∙ Couplers ∙ In-Line Filter Kits Dump Pumps & Walking Floor Pumps ∙ Gear Pumps & Motors Clamps ∙ Gaskets ∙ Steel Spacers & More! **Please provide transmission model and percentage engine speed required for application** Walking Floor Pumps Gear Pumps & Motors Hotshift PTO Hydraulic Tank & Mounts Dump Pumps Towers & Controllers Hose Kits w/ Fittings • PTO housing is made of cast iron with an increased mounting flange radius for heavy duty applications. • World American uses a cast iron rotatable flange with tapped holes makes installing the pump easier. The plug and gasket are included to increase the life of the splines. • World American PTO mounting kit include 2 studs to make installation of the PTO easier. Power Take-Off Units Metric Stud Kit MW1WA20-03-1060 Metric Stud Kit MW1WA20-03-1056 CATALOG NUMBER 24
MW1WAA50SS Aluminum Saddle GASKETS STEEL SPACERS Other Thicknesses Available 6-Bolt 8-Bolt 6-Bolt 8-Bolt Thickness MW1WA6010 MW1WA8010 .010 MW1WA6020 MW1WA8020 .020 MW1WA6032 MW1WA8032 .032 6-Bolt 8-Bolt Thickness MW1WA6062 MW1WA8062 .062 MW1WA6093 MW1WA8093 .093 Adapter Gears Available! Base dimensions are 4 1/2” x 5” to center of the bolt holes. These towers will accommodate our current dual controllers and our single controller. These towers are made of sturdy steel construction. The single controller operates the engagement and disengagement of the PTO. The dual controller operates the engagement and disengagement of both the PTO and the pump. Includes hose, fittings, valve, and LED Light MW1WA101X Single Controller MW1WA201X Dual Controller with Kickout MW1WA202X Dual Controller w/o Kickout MW1WA600221 8" Tower MW1WA600222 10" Tower MW1WA600223 12" Tower PTO CONTROLS & ACCESSORIES PTO Towers PTO Air Controller Kits TANKS ALL TANKS HAVE TWO (2) 2" NPT SUCTION PORTS The valve is a more defined 3 position 4 way feathering valve. Features precise control & feathering while dumping a load of stone or asphalt. Comes with a heavy duty body & control lever. Also equipped w/ a safety lockout device to prevent unintentional lever movement. MW1WA4306-10 10' PTO Cable MW1WA4306-15 15' PTO Cable MW1WA4306-20 20' PTO Cable MW1WA4306-25 25' PTO Cable PTO Cables PTO Feathering Valve MH1MPN600507 Console Tower for Feathering Valve - BY K1010C P/N BY AS1 - To air shift w/ feathering valve • Integral load holding check valves prevent reverse flow through valve when shifting • Balanced, select-fit spools provide minimum leakage, smooth operation • External spool seals permit easy replacement, reduced maintenance cost • Single Spool (4-Way Spool Action) • Rated Working Pressure 2500 PSI • Max. Shock and Surge Pressure 4000 PSI • Rated Flow Capacity 30 GPM • 3/4” SAE inlet and outlet ports; 3/4” SAE work ports • Integral differential poppet type relief valve, adjustable Directional Control Valves - BY HV11AG00D0 HANDLE SOLD SEPARATELY (P/N BY VH1) STEEL TANKS Gallons Sidemount Saddle Upright 10 MH1MHA-3100 - - 15 MW1WAS15S - - 35 - MW1WAS35S - 50 - MW1WAS50S MW1WAS50U 70 - - MW1WAS70U POLYETHYLENE TANKS Gallons Sidemount Saddle Upright 50 - - MW1WAP50U MOUNTING KITS FOR TANKS All kits come with hardware to complete installation. MW1WASMSK Black Steel Strap for 10, 15, 35, 50 and 70 Gallon Saddle Mount Tanks MW1WASBKSS Stainless Steel Strap MW1WAP50U Polyethylene Upright ALUMINUM TANKS Gallons Sidemount Saddle Upright 15 MH1MHA-4150 - - 35 - MW1WAA35S MW1WAA35U 50 - MW1WAA50S (With Steel Straps) MW1WAA50SS (With Stainless Steel Straps) MW1WAA50U 70 - - MW1WAA70U CAST IRON SHIFT COVER HOUSING AND STEEL SHIFTING FORK NEARLY ELIMINATE LEAKS AND ENGAGEMENT ISSUES THAT PLAGUE OTHER BRANDS IN THE MARKET. PTO Sending Unit Wiring Harness MW1WASWK-699 BY TC0015 Replacement Cap with Chain MW1WA091 Flange to Pump Gasket Neutral Lockout Toggle Valve Only - Momentary Switch BY BAV020T
World American C & G Pumps are known for their ruggedness, reliability and interchangeability. Available in both the 101 Remote Mount and the 102 Direct Mount configurations and C or G frames, these pumps offer cast iron construction, a variety of displacements and “Air Shift” capabilities. • Bi-Rotational • Pressures up to 3000 psi • Flow rate (GPM) at 1000 rpm • Dual Porting, side and rear, ORB or NPT • Options, 7-Displacements, 2-Shafts, 2-Porting • Universal ports, ports are as large as possible to fit a variety of applications, use steel adapters to fit your application! We have a full line of adapters to fit your application. • Bi-Rotational • Pressures up to 3000 psi • Speeds up to 3600 rpm • Flow rate (GPM) at 1000 rpm • Dual Porting, side and rear, ORB or NPT • Combination Mounting Flange, 2/4 Bolt, SAE “B” • Hi-Flow body design for increase flow and performance • Universal ports, ports are as large as possible to fit a variety of applications, use steel adapters to fit your application! We have a full line of adapters to fit your application. Walking Floor dual pressure 2000 psi for dump bodies, and 3000 psi for live floor trailers. Pressure switching is controlled from the air supply of the truck. Heavy duty roller bearing construction. Standard with air shift, bracket and mounting hardware. MW1WAP101-25AS Remote Mount, Air Shift MW1WAP102-25L Direct Mount w/o Air Shift MW1WAP102-25LAS Direct Mount with Air Shift P/N GPM @ 1000 RPM MW1WAK20B8ANX 8 MW1WAK20B11ANX 11 MW1WAK20B13ANX 13 MW1WAK20B15ANX 15 MW1WAK20B17ANX 17 P/N GPM @ 1000 RPM MW1WAL51B-19ANX 19 MW1WAL51B-23ANX 23 MW1WAL51B-25ANX 25 MW1WAL51B-27ANX 27 MW1WAWFDPUMP Dual Pressure Pump MW1WAPBK-1001 6-Bolt Dump Pump Mounting Bracket MW1WAPBK-1000 8-Bolt Dump Pump Mounting Bracket WAK20 Series GPM @ 1000 RPM WAL51 Series GPM @ 1000 RPM DUMP PUMPS & WALKING FLOOR PUMPS GEAR PUMPS & MOTORS IN-LINE RELIEF VALVES BALL VALVES HYDRAULIC QUICK COUPLERS Wing Nut Style Couplers - Female Matching Nipple - Male Tip P/N Port Size GPM BY HRV07518 3/4” NPT 20 BY HRV10018 1” NPT 30 BY HRV10025 1” NPT 50 P/N Description TC 2005-16 1” ball valve TC 2005-20 1-1/4” ball valve TC 2005-24 1-1/2” ball valve P/N Thread Style Body Size Thread Size GX QS515W-06 NPF 3/4” 3/4-14 GX QS515W-08 NPF 1” 1-11 1/2 GX QS515W-10 NPF 1-1/4” 1 1/4-11 1/2 P/N Thread Style Body Size Thread Size GX QS511-06 NPF 3/4” 3/4-14 GX QS511-08 NPF 1” 1-11 1/2 GX QS511-10 NPF 1-1/4” 1 1/4-11 1/2 MW1WA925FH • 150 PSI working pressure • Flows up to 50 GPM for return & 15 GPM for suction line applications • Four 1/8” NPT Gage Ports MW1WADFH4 • 150 PSI working pressure • Flows up to 90 GPM for return and 20 GPM for suction line applications • Both 1-1/2” NPT and 2” SAE Ports IN-LINE FILTERS Replacement Filter: LF PH725 Replacement Filter: LF LFP449 (filter sold separately) Part numbers listed are 7/8" 13 Spline Shaft LUC10017 Gallon LUC10037 5 Gallon Pail LUC10038 55 Gallon Drum Special Order LUC10401 AW ISO 32 Hydraulic Oil/1X1 / 5 Gal. LUC10404 AW ISO 46 Hydraulic Oil/1X1 / 5 Gal. UNIVERSAL HYDRAULIC FLUID HYDRAULIC OIL We recommend a support bracket on all C & G pumps.
MIDWESTWHEEL.COM MEMBER KANSAS CITY 5801 E. Front St. Main ....(816) 471-1552 Parts....(800) 821-7402 JOPLIN 2424 Stephens Blvd. Main ....(417) 717-6022 Parts....(866) 318-9111 SPRINGFIELD 812 Lillian Dr. ∙ Strafford, MO Main ....(417) 429-2476 Parts....(800) 785-3705 SIOUX CITY 1819 4th St. Main ....(712) 252-7969 Parts....(800) 943-3534 CEDAR RAPIDS 200 50th Ave. S.W. Main ....(319) 365-4453 Parts....(800) 332-5435 DES MOINES 1436 E. Ovid Ave. Main ....(515) 265-1491 Parts....(800) 888-0248 CLEAR LAKE 840 Hwy. 18 W. Main ....(641) 357-7101 Parts....(800) 397-5630 DAVENPORT 8502 Northwest Blvd. Main ....(563) 322-2671 Parts....(800) 553-1886 OMAHA Main ....(531) 239-3050 Parts....(800) 322-8757 NEBRASKA IOWA MISSOURI January 8, 2024 (24PTO and Wet Line Kits) HYDRAULIC HOSE SUCTION/RETURN LINE DESERT™ HR4 LOW PRESSURE HOSE SAE 100R4 Meets Flame Resistance USMSHA Designation P/N Hose Size Inch Max. Working Pressure Min. Bend Inch Min. Burst PSI GX HR4-12X100CL 3/4 300 2.5 1200 GX HR4-16X100CL 1 250 3.0 1000 GX HR4-20X100CL 1-1/4 200 4.0 800 GX HR4-24X100CL 1-1/2 150 5.0 600 Compatible fitting options: • UC fitting w/UCF-6 Collars • Hose barb fittings w/clamps Application: Low pressure, high temperature return line or suction line for petroleum and water-based hydraulic fluids Inner Tube: Nitrile Reinforcement: Spiral-plied synthetic fabric with wire helix Cover: Black neoprene Temperature Range: -40°F to 275°F Fittings: 2 Piece Crimpable P/N Hose Size Inch Max. Working Pressure Min. Bend Inch Min. Burst PSI GX XR16SC‐04X590RL 1/4 5800 2.0 23200 GX XR16SC‐06X460RL 3/8 5000 2.5 20000 GX XR16SC‐08X390RL 1/2 5000 3.5 18000 GX XR16SC‐10X260RL 5/8 4350 4.0 16000 GX XR16SC‐12X200RL 3/4 3500 5.0 14000 GX XR16SC‐16X200RL 1 3000 6.0 10800 Compatible fitting options: • B2 Series crimp fittings Application: High pressure service with tight bends for petroleum and water based hydraulic fluids. Excellent impulse performance and flexibility exceeding SAE 100R2 and SAE 100R16 standards Inner Tube: Nitrile Reinforcement: Two braids of high-tensile steel wire Cover: Black synthetic rubber Temperature Range: -40°F to 212°F PRESSURE LINES XR16SC HIGH PRESSURE HOSE SAE 100R16/857 2SC Meets Flame Resistance USMSHA Designation • Meets Higher EN/DIN Pressures We stock a complete line of hose & fittings - Please reference our Continental Hydraulics Catalog for complete details! GENERAL PURPOSE CLAMPS P/N Min. Dia. Max. Dia. IDL6506E 51 9/16" 13/16" IDL6508E 51 11/16" 15/16" IDL6510E 51 13/16" 1-1/16" IDL6512E 51 15/16" 1-1/4" IDL6516E 51 13/16" 1-1/2" LINED CLAMPS P/N Min. Dia. Max. Dia. IDL47010 51 13/16" 1-1/16" IDL47012 51 15/16" 1-1/4" IDL47016 51 13/16" 1-1/2" IDL47020 51 13/16" 1-3/4" CONSTANT TORQUE CLAMPS P/N Min. Dia. Max. Dia. IDL62040 51 7/32" 5/8" IDL62060 51 1/4" 25/32" IDL5706 051 7/16" 25/32" IDL5708 051 1/2" 29/32" IDL5710 051 9/16" 1-1/16" IDL5712 051 11/16" 1-1/4" IDL5716 051 13/16" 1-1/2" CLOSE NIPPLE COMBINATION NIPPLE HEX BUSHING 90° FEMALE PIPE ELBOW GHD57-140 1-1/2" GHD57-120 1-1/4" GHDSTC-5 3/4" MW1WABH100 1" MW1WABH125 1-1/4" GHDSTC-20 1-1/2" GHD65-531 2 x 1-1/2" GHD65-530 2 x 1-1/4" GHD65-107 1-1/2" GHD65-106 1-1/4"
www.midwestwheel.comRkJQdWJsaXNoZXIy MTEyNjY3NA==