GOLD SEAL® CHAMBERS LIFE SEAL® ACTUATORS Isolated Chamber Prevents Spring Fracture Compression spring fracture is the major cause of all spring brake failures. Water, salt, oil and other contaminants attack and weaken the spring causing corrosion and ultimately, failure. Since the Life Seal chamber is completely sealed, contaminants cannot reach the power spring. The spring housing does not contain vent holes, external breather tubes, cage tool plugs or filters so the spring is isolated from the external environment. A special internal valve allows air to escape through the vehicles’ air system instead of through the housing. Life Seal Maximizes Output Force Most new spring rakes meet a minimum required output force. The ability for that spring to maintain output force is lost over time. Through technological innovation, Life Seal is the only actuator to maximize output force over an extended period. A unique patented power spring maintains high output force while increasing strength. The center tube guides the form-fit pressure plate, which stabilizes the spring coil through the full range of travel. This prevents contact with the spring housing and dramatically reduces coil clash. Delivering Reliability, Long Life and Value SPRING BRAKE CHAMBERS GOLD SEAL CHAMBERS Durability and Reliability Mile After Mile Save Time & Ensure Accuracy with Pre-Cut Push Rods • Reduce out-of-service time by adding extra push rod clearance to your brake chambers • Standard on some applications • More push rod force at or near the recommended readjust position compared to conventional brake chambers • 4 Year Over the Road/2 Year Severe Duty Warranty SPRING BRAKES 2 YEAR UNLIMITED MILE WARRANTY Permanently sealed spring chamber for maximum safety. Push Rod Diameter: 5/8” Includes: Caging tool, clevis (when applicable) and stroke indicator COMPLETE ASSEMBLIES P/N Type Stroke JW MAX3030LWC Type 30/30 LS w/ Welded Clevis 3.00" JW MAX3030LSC Type 30/30 LS w/ Clevis 3.00" JW MAX3030WC Type 30/30 w/ Welded Clevis 2.50" JW MAX3030NC Type 30/30 No Clevis 2.50" JW MAX3030H Type 30/30 Intraxx 2.50" PIGGY BACK KITS P/N Type Stroke JW MAX3030PBK Type 30/30 2.50" JW MAX3030PBKLS Type 30/30 LS 3.00" COMPLETE ASSEMBLIES P/N Type Stroke AK LCP3030 Type 30/30 2.50” AK LCP3030L Type 30/30 LS 3.00" 6 Year Unlimited Mile Warranty P/N Description Push Rod Length Stroke AK GC3030S2 Most trailers w/ clevis 5.70” 2.50” AK GC3030S3 Fits most trucks/tractors w/ clevis 1.8” 2.50” AK GC3030CW Type 30/30, Precut 2.25” Welded Clevis 1.0” 2.50” AK GC3030LCW Type 30/30, Precut 2.25” Welded Clevis 1.0” 3.00” PIGGY BACK KITS P/N Type Stroke AK LPP3030K Type 30/30 Kit 2.50” COMPLETE ASSEMBLIES P/N Type Stroke AK GC3030 Type 30/30 2.50” AK GC3030L Type 30/30 LS 3.00” AK GC3030LCW Type 30/30, Precut 2.25” Welded Clevis 3.00” AK GC3030LR Type 30/30 LS, 14” Push Rod 3.00” AK GC3030R Type 30/30, 14” Push Rod 2.50” AK GC3030S2 Trailer Pre-Cut 6.89” w/ Clevis 2.50” AK GC3030S3 Trailer Pre-Cut 3.02” NO Clevis 2.50” PIGGY BACK KITS AK GP3030K Type 30/30 Kit 2.50” AK GP3030LK Type 30/30 LS Kit 3.00”
RkJQdWJsaXNoZXIy MTEyNjY3NA==